China Good quality High-Quality 1500bar Road Marking Line Removal Cleaning Equipment Good Price near me shop

Product Description

High-Quality Old Road Marking Removal Cleaning Equipment

Introduces:

The ultra-high pressure water flow generated by the booster equipment loaded on the light truck is continuously fed into the hand-push washer through the hose, and then sprayed on the road at a high speed. The maximum pressure of the water can reach 300 MPa, which is 3061 kgf/cm². After the washing machine pushed through, the road surface was intact and the painted marking lines on the road were cleaned up after being swept by the high-pressure water flow.

Features of the whole machine:

1. The equipment adopts CZPT brand diesel engine of the United States.
2. The pump adopts high-quality German technology and design, which is efficient and reliable.
3. The connection between the pump and the diesel engine adopts a flexible coupling design with low noise
4. Split type high pressure pump, each alloy-coated plunger has an independent cooling system.
5. The integrated oil cooling system provides a reliable guarantee for the long-term stable operation of the pump
6. Trailer type or truck type installation can be selected by users.
7. The control cabinet is CZPT original, digital display control panel, humanized control interface, and various sensor signal displays.
8. The pressure-sensing diesel engine fuel-saving device adopts American technology. It is a specially designed fuel-saving device with a fuel-saving rate of 20-30%.

Manual Cleaning Cart Features:

1. The manual cleaning cart is equipped with a height adjustment device, which can adjust the height of the rotating head arbitrarily, which is convenient to use.
2. The washing truck is designed with a remote control switch, which can remotely control the switching of high and low pressure working states.
3. The original design of the rotating mechanism can support an extremely high pressure of 1500 bar.
4. The rotating head is driven by a 24V motor and adopts gear transmission, which is much more durable than belt transmission without loss.
5. The maximum cleaning width of the rotating head can reach 200mm, and the cleaning speed is faster.
6. The rotating head is equipped with a circular protective cover, and a dirt suction device can be added to ensure a clean and tidy work site.

Technical Parameters:

Maximum Working Pressure: 1500Bar
Maximum Input Power: 90KW
Plunger Diameter: 18mm
Gear Reduction ratio: 2.76
Equipment Size: 2.7 meters long, 1.7 meters wide, 2 meters high
Maximum Water Consumption: 26L/M
Pump Speed: 525R/M
Stroke: 66mm
Comprehensive Fuel Consumption: 11-14L/M
Load: 2.5 tons
 

Type Input Speed(min-1) 1485 Pump stroke 92mm
DLS90 Pump Speed(min-1) 280 314 343 469
Plunger Diameter(mm) Pressure(Mpa) Flow(L/min) Power(kw) Flow(L/min) Power(kw) Flow(L/min) Power(kw) Flow(L/min) Power(kw)
30 50 54.5 55 59.9 75 65.5 75 89.5 90
45 23 122.8 55 134.8 75 147.3 75 201.4 90
50 18 151.6 55 166.5 75 181.8 75 248.6 90
56 14 190.2 55 208.8 75 228.1 75 311.9 90
60 12 218.3 55 239.7 75 261.8 75 358.0 90
64 10 248.4 55 272.7 55 297.9 75 407.4 90

  

Type Plunger Diameter(mm) Flow(L/min) Input Speed(min-1) Pressure Corresponding To Power(Bar)
90kw 110kw 132kw
DLS132 14 20 1500 2400 2800
16 25 1500 1900 2300 2700
18 32 1500 1400 1800 2100
20 40 1500 1200 1400 1700
22 47 1500 1000 1200 1400
24 57 1500 800 1000 1200
26 67 1500 700 850 1000
28 78 1500 600 720 900
30 90 1500 520 650 800
32 102 1500 450 550 700
34 115 1500 400 500 600
36 129 1500 350 450 550
38 143 1500 320 400 500
40 160 1500 300 350 450
42 175 1500 260 320 400
44 192 1500 240 300 350

 

Type Plunger Diameter(mm) Flow(L/min) Input Speed(min-1) Pressure Corresponding To Power(Bar)
160kw 200kw 250kw 300kw
DLS300 18 33 1500 2400 2780
20 41 1500 1950 2430 2780
22 50 1500 1600 2000 2500
24 60 1500 1330 1666 2000 2500
26 70 1500 1140 1428 1785 2100
28 81 1500 985 1234 1500 1800
30 93 1500 860 1075 1350 1600
32 106 1500 755 940 1150 1400
34 120 1500 666 830 1040 1250
36 134 1500 595 745 930 1120
40 165 1500 485 600 755 910
45 210 1500 380 475 595 710
50 258 1500 310 385 480 580
55 312 1500 255 320 400 480
60 372 1500 215 270 335 400
65 436 1500 180 230 285 340
70 507 1500 157 197 245 295
75 582 1500 137 172 214 255

1. Suitable for high-pressure and ultra-high-pressure cleaning pumps, petroleum, chemical, fertilizer process pumps, copper liquid pumps, oil fields, salt mines, liquid carbon dioxide pumps, 5 sodium slurry pumps, steel plant dephosphorization pumps, rust removal pumps, spunlace Non-woven pump.
2. Assembly method: horizontal, vertical, fixed, mobile.
3. Transmission mode: electric motor, diesel engine, gear box, belt pulley, electromagnetic speed regulation, frequency conversion speed regulation.
4. The technical parameters in the table are used as reference for selection. Each pump is equipped with a safety pressure regulating valve, and the pressure of the pump can be adjusted arbitrarily
5. The flow rate in the selection table is inappropriate. Electromagnetic speed regulation, frequency conversion speed regulation, and plunger diameter can be used to adjust the flow rate to meet the selection requirements.
6. The pump body materials include alloy steel, martensite, austenitic stainless steel, 316, 205L duplex steel.

Types of pulleys and their advantages and disadvantages

There are several types of pulleys. Learn the basic equations of the pulley system. Then learn about the different uses for pulleys. The disadvantages of using pulleys will be covered. Knowing these, you can buy the pulley that suits your needs. Here are some of the best pulley types and their pros and cons.
pulley

Basic equations of pulley systems

A pulley system is a mechanism that allows 2 blocks of a certain mass to be connected by a taut rope. The acceleration of each block is the same in magnitude and direction. The external force acting on each block is the weight of the block (10g) and the tension in the string. The tension between the 2 blocks is the total tension and the force acting on the pulley is the weight of the 2 blocks.
This simple mechanism uses 2 simple equations to explain how the system works. First, the mass of the weight on both sides of the pulley must be the same. When the weight is forced to move, the rope tightens and the second pulley descends. The weight is also attached to the second pulley and must be the same distance as the first pulley. This will result in a speed ratio of 2 times the distance covered by the first pulley.
Second, we have to calculate the force required to lift the object. The lower mass is supported by a wire configuration passing through all pulleys, while the uppermost pulley is used to apply the force. The lower block is used to support the weight. The applied force needs to travel a distance nx to move the weight. This distance, called MA, can be written as:
Once we have gathered the necessary information, we can apply the calculations to the pulley system. We can also use the Mechanical Advantage Calculator to calculate the force on the anchor. To do this, we must apply a force to the load as well as to the pulley itself. Using this equation, we can calculate the force required by the load to lift the load.
pulley

Types of pulleys

There are 3 basic types of pulleys: movable, fixed and compound. Both types of pulleys translate the force applied to them. The ideal mechanical advantage of pulleys is two. This is because a single movable pulley only doubles the force, whereas a compound pulley doubles or triples the force. This type of pulley is often used with other types of pulleys.
Movable pulls move with the weight of the load, and the force pulling them increases on the lift side. They are often found in utility elevators and construction cranes. These systems are very simple, inexpensive and quiet to use. The force required to lift the object depends on the mechanical advantage of the system. The 2 most common types of pulleys are listed below. Let’s take a closer look at each one.
V-shaped pulleys are used in vehicles and electric motors. These pulleys require a “V” belt to function properly. Some have multiple “V” grooves to avoid slipping. They are used in heavy duty applications to reduce the risk of power slip. These pulleys also have more than 1 “V” groove. V-belt pulleys are commonly used in vehicles and electric motors.
Composite pulleys are made from more than 1 type of cable or rope wrapped around the wheel. They can be fixed or hinged and are usually made of stainless steel or bronze. Composite pulleys have multiple layers and can be a single unit or many different components. There are 3 main types of pulleys: fixed pulleys and composite pulleys. These are the most common types. Almost every type of pulley is used for some type of application.
Fixed pulleys have 1 advantage over movable pulleys: they change direction as the weight of the load increases. They are typically used in heavy construction equipment. Gun tackles, patio tackles, and stationary tackles are examples of equipment that use a pulley mechanism. These devices are very common and can be found on most modern construction sites. They provide great convenience for lifting large loads.

application

What are the applications of pulleys? Simply put, a pulley is a mechanical device that transforms a difficult task into an easier one. It consists of ropes and pulleys. It is usually used to lift objects. Usually, people wrap a rope around a pulley and pull up to lift the object. One disadvantage of using pulleys is that they require the same force as lifting the object directly.
One of the most popular applications of pulleys is lifting heavy objects. They help people pull up heavy objects and blocks. The system can also be used in seeders, lifts, grinders, etc. Other applications include raising flags, loading cargo, pulling curtains and rock or mountain climbing. Students can learn about the various uses of pulleys and the physics behind them.
Pulleys can be made of many different materials, depending on the application. Some are movable, which means they move with the object they are used to lift. This pulley system can be made of nylon, wire rope or fiber material. The best part about these systems is that they are easy to install and maintain. For a better grasp, use the guide or video tutorial to learn more about the pulley system and how it works.
Tapered pulleys are common in paper mills. They are high-quality pulleys that transmit power to connected parts. They can be dynamic or static and have different balances. Because pulley systems are highly customized, most industrial applications require systems designed specifically for specific applications. In this way, the system is safe, simple and inexpensive. The benefits of this design are endless.
The most common use of pulleys is for motor drives. They are used to minimize noise by applying force to the shaft to reduce the workload. They are also less expensive than gears and do not require lubrication. Furthermore, they can change the direction of the applied force. They are also less expensive than gears and are often used with other components. A screw is a cylindrical member with helical ribs used to connect something.
pulley

shortcoming

Although the pulley system makes it easier to move heavy objects, it still has some drawbacks. When using a pulley system, you must remember that the force required to lift the weight increases with the number of cycles. In addition, the distance between the puller and the heavy object increases, which may lead to accidents. Also, moving heavy objects can be tricky if the rope slips. Pulley systems are not very expensive and can be easily assembled. However, it does require a lot of space.
First, it is not efficient. Besides being inefficient, pulleys produce different forces at different speeds. Fixed pulleys use more force than the load, while movable pulleys move with the load. A movable pulley requires less force than a fixed pulley, but the combined system travels a long distance. Therefore, this method is not as efficient as the fixed method.
Pulleys are not only used in industrial processes. You can see them in various places in your daily life. For example, large construction cranes use pulleys to lift heavy loads. Even flagpoles, blinds, clotheslines, ziplines, motors and climbing equipment use pulleys. Still, despite their advantages, the disadvantages are not too serious.
Another disadvantage of the pulley is its wear and tear. While a pulley’s housing is theoretically infinite, its bearings and locking components typically wear out over time. To overcome this problem, a new bearing and locking assembly can be installed. No need to replace the housing and shaft, the entire assembly can be re-bonded and painted to replicate the original look. Alternatively, the pulley can be replaced with a new housing and shaft.
Using pulleys can also reduce the advantage of pulleys. On the other hand, interception and tackle is a system in which 2 pulleys are connected to each other using ropes. Unlike pulleys, pulley pulley systems can be adjusted in the direction of travel and can move heavy loads up to 4 times their force when used in hydraulic lifts.

China Good quality High-Quality 1500bar Road Marking Line Removal Cleaning Equipment Good Price     near me shop China Good quality High-Quality 1500bar Road Marking Line Removal Cleaning Equipment Good Price     near me shop